• Installation Instructions Wireless ADSL2+ Router Huawei HG530 / HG530u. • Contents Minimum System Requirements.. 3 Package Contents..4 LEDs...5 Ports...6 Connecting the ADSL2+ Router.. 7 PSTN Line...8 ISDN Line...11 Internet Settings..14 Wireless Connection..19 Turning the wireless network On/O /& Reset Router..24 Change the Username &. Mar 6, 2017 - Default login password: admin. Huawei HG530 - Wireless ADSL Modem Router. It is a draft-n router, compatible with 802.11n standard. In general, modem router is not supported plus it has only 2M of flash. Hence, the chance of dd-wrt support is very very slim. May 14, 2013 En este video puedes observar como entrar a la confguracion del modem, ya que une cambio la entrada normal al modem Mayo-2013. Configuracion Router CNT - Huawei HG530. • Minimum System Requirements 1 Pentium 4 Processor 2 Windows XP/Vista/7 or Mac OS 9.x 3 1 GB RAM 4 25 MB free hard disk space 5 10/100 Mbps Ethernet Network Card. • Package Contents 1 ADSL2+ Wireless Router 2 Telephone Cables (RJ-11) 1 Ethernet Cable (RJ-45) 1 Installation CD 1 Power Transformer 1 Splitter Installation Instructions 1 Filter (for PSTN) Installation Instructions Wireless ADSL2+ Router Huawei HG530 / HG530u. • LEDs The following LEDs are found on the front side of the ADSL2+ Router. Clave De Router Huawei Hg530 EtbThe Huawei EchoLife HG532 router has 300mbps WiFi, 4 100mbps ETH-ports and 0 USB-ports. Quick links: Default password/Login Login instructions. Problem on network. HUAWEI HG530. Discussion in 'Networking' started by IreneGR, Mar 5, 2012. IreneGR Thread Starter. Joined: Dec 8, 2011 Messages: 17. Guys a few days ago, I changed my net and I was given the router HUAWEI HG530. But while playing Lineage II, it disconnects me from the game and the connection goes slow. Review the meaning of each LED below (Figure 1). Figure 1 Color Status Meaning Connection established Connection is not established Blinking Connection being established Connection established Connection is not established •. • Ports The ADSL2+ Router has the following buttons and ports (Figure 2): PORT LABEL DESCRIPTION OPERATION This port is used for POWER Power Port the 220V power transformer RESET Factory setting reset button Resets factory settings Connects to OTE’s Cable Television LAN 4 (STB) Ethernet Port for decoder over Internet Service. • Connecting the ADSL2+ Router Connecting the ADSL2+ Router Follow the following instructions to connect the ADSL2+ Router over a PSTN or ISDN telephone line. ![]() • PSTN Line If you have a PSTN telephone line (plain analog line), connect the ADSL2+ Router as shown below. Magi astrology software free download. • PSTN Line If you have a telephone set connected to the telephone socket, you must disconnect it. Using the blue cable, connect the blue port on the splitter to the telephone socket. Use the grey cable to connect the grey port on the splitter to the grey port on the Conn-x equipment. • PSTN Line Connect the power transformer to the power port on the Conn-x equipment and plug it to the mains socket. Press the ON/OFF power button located on the side of the equipment, to turn on your equipment. The Power, ADSL, Internet, LΑΝ and WLAN LEDs will light. To connect additional telephone sets to other sockets, each set must be connected to a lter. • ISDN Line If you have an ISDN telephone line, connect the ADSL2+ Router as shown below. • ISDN Line Disconnect the cable that connects the telephone set to the ISDN equipment (N.T. 1) from the telephone socket and connect it to the black port on the splitter. Using the blue cable, connect the blue port on the splitter to the telephone socket. • ISDN Line Use the yellow cable to connect the network port (ETHERNET) of your computer to one of the three rst yellow ports on the Conn-x equipment. WARNING: The purple port labeled STB is used exclusively to connect the set-top-box required to receive OTE's Cable Television over Internet service. • Internet Settings Internet Settings To install the ADSL2+ Router, insert the CD in the CD-ROM drive. The CD must start automatically. ![]() If the CD fails to start automatically, go to Windows Explorer, select the CD-ROM drive where the CD is located, double click on setup.exe and follow the instructions. • Internet Settings Open your Browser. At the address line type and press Enter. The screen shown on the side will appear: The ADSL, ATM, and Internet Status LEDs must be green. If one of the LEDs is red, check the connections and try again. • Internet Settings Click on Administration. The screen shown on the side will appear. • Internet Settings Enter admin in the Username eld. In the Password eld enter the password you will nd on the label on the back of your ADSL2+ Router and click on ΟΚ. Note the Username and Password on the last page of the brochure. • Internet Settings The screen shown on the side will appear: In the Username eld enter the username you were given at the time of purchase of your Conn-x package followed by @otenet.gr In the Password eld enter the password you were given at the time of purchase of your Conn-x package. • Wireless Connection Wireless Connection Follow the instructions below to connect wirelessly to the Internet. • Wireless Connection To connect wirelessly to the Internet you must have completed the Internet Settings. If you wish to connect from a desktop computer, you must have installed and activated the wireless USB stick or wireless network card on your computer. If you wish to connect wirelessly from a laptop you must have activated the wireless mode (see the user manual that came with your laptop). • Wireless Connection Double click on the wireless network icon on your computer to display available wireless networks. • Wireless Connection The name of your wireless network that you must look for is the one that has the SSID name you will nd on the label on the back of your equipment or on the CD jacket. ![]() Note the SSID name on the last page of the brochure. Click on the wireless network that corresponds to the SSID name and click Connect. • Wireless Connection On the screen that will appear enter the WPA network security key you will nd on the label on the back of your equipment or on the CD jacket labeled WPA, and click on ΟΚ. Note the WPA network security key on the last page of the brochure. • Turning the wireless network On/O /& Reset Router The wireless mode is on.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |